0

 

 

Notions:

  • 1 metre or 1 yard of fabric
  • 1 metre or 1 yard of thin wadding
  • Sand
  • 1 metre or 1 yard of calico
  • Piping 2.75 meters or 3 yards

 

 

Instructions for making the Cuddles the Cat door stop

The following instructions are for those who wish to position the cats face to the body

 

 

1

 

  • The pin is showing you the centre of the cross on the top of the cats body (Cat front body_240x150)
  • Once you re- hoop for the “Cat Face_01” leave room for you to manoeuvre your needle for the needle to be placed exactly in the centre of the cross as shown in the above photo, no need to stitch the cross out on the face as this is the exact spot for the needle when you go to the second colour in your colour chart

 

2

 

Cut out the front panel of the door stop the size that would best suit you then match up the front with the back panels

 

3

 

Matching the front panel with the back panel using pins

 

4

 

Cut the back panel the same size as the front panel

 

5

 

Front and back panels cut to the exact same size

Please take note


A big mistake I made stitching this door stop out ...The mistake was not using a thread colour that would stand out for the body of the cat, I should have used black thread which would have defined the cats body so much more clearer

 

  • I used sand to make the door stop heavier, you can buy sand from the local hardware store in a packet, put the sand on a baking tray and then put the sand into a hot oven for about 15 minutes, this kills any bugs that could be in the sand
  • Stitch a bag just slightly smaller than the size of your door stop I used calico and I stitched two layers for all sides as this would stop any leakage of sand getting through

 

6

 

Stitch the bottom panels together

 

 

 

Instructions for the Door Stop with side panels

 

7

 

Stitch the front and back panels out, then mark out how big you would like the door stop

 

8

 

Mark out all four sides, I used the width of a ruler

 

Cuddles the Cat Machine Embroidery Designs

 

As you can see the side panels are the width of the ruler then I stitched a sewing machine foot in width for the seam (I find it easier this way, you do it the way that best suites you)

 

10

 

On the front panel stitched a black and white gingham piping

 

11

 

  • On the back panel black and white gingham piping also
  • I used sand to make the door stop heavier, you can buy sand from the local hardware store in a packet, put the sand on a baking tray and then put the sand into a hot oven for about 15 minutes, this kills any bugs that could be in the sand
  • Stitch a bag just slightly smaller than the size of your door stop I used calico and I stitched two layers for all sides as this would stop any leakage of sand getting through

 OnlineCasino

 

  

Machine Embroidery Designs

 Latest Releases

 

Folklore Machine Embroidery Designs

Released on the 25th June 2019

 

 Folklore Machine Embroidery Designs by StitchingArt

  

6 designs included in the Folklore machine embroidery design set.

The Folklore design is suitable for a 6 x 10 inch or 240mm x 150mm hoop.

The Folklore design is available in DST, EMB, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart is included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EMB or EXP format. Sorry for the inconvenience.

View the Folklore Machine Embroidery Designs

Mayil Machine Embroidery Designs

 
Mayil Machine Embroidery Designs

 Released on the 28th May 2019

6 designs included in the Mayil machine embroidery design set.

The Mayil design is suitable for a 14 x 8, 14 x 7 or 360mm x 200mm, 360mm x 150mm hoop.

The Mayil design is available in DST, EMB, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart is included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EMB or EXP format. Sorry for the inconvenience.

View the Mayil Machine Embroidery Designs

 

springoflife4

 

Spring of Life Machine Embroidery Designs

 Released on the 27th April 2019

9 designs included in the Spring of Life machine embroidery design set.

The Spring of Life design is suitable for a 5 x 7, 6 x 10, 8 x 12 inch or 180mm x 130mm, 240mm x 150mm and 360mm x 200mm hoop.

The Spring of Life design is available in DST, EMB, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart and instructions are included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EMB or EXP format. Sorry for the inconvenience.

 View the Spring of Life Machine Embroidery Designs

 

 

Wild and Free Machine Embroidery Designs

 

Wild and Free Machine Embroidery Designs

 Released on the 2nd February 2019

6 designs included in the Wild and Free machine embroidery design set.

The Wild and Free design is suitable for a 6 x 10 inch or 240mm x 150mm hoop.

The Wild and Free design is available in DST, EMB, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart and instructions are included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EMB or EXP format. Sorry for the inconvenience.

 View the Wild and Free Machine Embroidery Designs