Tranquility Cushion 

 
 Notion
  • Seven separate Tranquility designs - "n01", "n02", "n03", "n04", "n05", "n06" and "lilly" designs.
  • Grey blue coloured linen (to portray early evening).
  • Navy blue coloured silk organza (for the water).
 
  Instructions
  Set up your chosen blue grey linen material in your hoop. Position your hoop at the top left hand side of your linen piece.

 

N01 Design

Stitch the 'n01." design
 

N02 Design

Reposition your hoop to the right hand side of and adjacent to the "n01.pcs" design which you have sewn. Next, stitch out the "n02." design
 

N03 Design

Reposition the hoop once again, to the right hand side of and adjacent to the "n02." design which you have sewn. Next, stitch out the "n03." design.

 

 

The combination and co-ordination of these three designs on your piece of linen will produce a lovely, serene, landscaped, rural scene.
 
  Position the top edge of your navy blue coloured voile material over the the base of the linen piece. Align it across your linen, approximately 8 cm (2.5 inches) below the centre of the landscape scene. It should be positioned just at the base of the tree trunks in that design, directly below the "n02." design. Pin down the piece of voile.
 
 

Sew the navy blue coloured voile material over the top of the piece of linen using mirrored stitch No. 79. It has the appearance of a grass stitch. Use a bottle green coloured thread. Ensure that you vary the stitch width as the machine is stitching. This will make the grass look a bit more realistic. Over the top of the grass stitch, free machine embroider more grass using khaki coloured thread.

 

N04 Design 

Reposition your hoop once again, so that when the head of the swan in "n04." design is stitched out, it is positioned so that it will stitch out on the linen, over the top of embankment. (That is, the top, grassy edge of the voile material piece). Please refer to the "n04 design."
 

N05 Design 

Once again, reposition your hoop and stitch the "n05." design, so that the second swan's head is positoned over the top to the rear of the first swan's body, (That is, to the bottom right hand side of the "n04." design which you have stitched out).
 

Lilly 

Reposition your hoop to the right hand side of the "n05" design. Stitch out the "lilly." design. Please refer to the design panels shown below.
 

N06 Design 

Once again move your hoop to the right. Stitch out the "n06." design to the right of the "lilly." design.
 
  To further enhance your tranquility pillow, sew No. 01 (double straight) stitch, using a pale blue coloured thread for the water, making fine curves.
 
 
 

  Swans Handkerchief or Jewellery Bag 

 

   
 Notions "swan.pcs" design.
Pale blue voile fabric.
Cream lining fabric.
Lace.
Pellum
 
  Instructions
 
  approximate hoop size is 21 x 21 cm or 8 x8 inches
 

Swan.PCS 

Stitch swan.pcs design onto a piece of blue voile fabric
 
  Cut the voile fabric containing the "swan" design into the shape of a triangle.
 
  Cut the cream lining into a triangle of the same size as the voile
 
  Stitch the voile and lining together
 

Diagram No 2

I realize that "hand stitching" is an unpleasant phrase for some of us, but I actually hand stitched the lace onto the triangle lip as shown in diagram No. 2.
 
  Cut other pieces of voile, pellum and lining 45 x 25 cm or 17 x 10 inches.
 
  Position the triangle lip at the long end, between the pellum and the lining and stitch together.

 
  Quilt the voile, pellum and lining together.
 

Diagram No 3 

Sew a bias binding over the raw edges on the front of the square. I suggest that you use the lining fabric as the bias binding. Sew some lace down from the edge, as in diagram No. 3.
 
  French seam the sides together.

 
 
 

  Bird of Paradise Bag

   

Diagram No 1 

Cut both the black fabric and lining material into identical circles of 40 cm (16 inches) in diameter, as shown in diagram No 1.
 
  Cut the plastic lid of an ice cream container into a circle of 6 cm (2.5 inches) in diameter.
 

Diagram No 2 

Fold the fabric circle in half (along the line of the diameter), as shown in diagram No. 2.
 
  Mark the centre point of both half circles of the fabric, on the outer side.
 
  Position your hoop over the centre marked on one side of the half circle of fabric.
 

Diagram No 3 

Stitch the "bird01.pcs" design on one side of of the half circle, as shown in diagram No. 3.
 

Diagram No 4

Over the centre mark of the other half circle, stitch the "birdaa.pcs" design, as shown in diagram 4.
 

Diagram No 5 

The two Birds of Paradise designs should now appear stitched out on your fabric as shown in diagram No. 5.
 

Diagram No 6 

Measure and mark the circular hem 15 mm (5/8 inch) in from the circumference (outer edge) of the circle of the fabric, as shown in diagram No. 6.
 

Diagram No 7 

Measure and mark another inner circle 17.5 mm (1 and 5/8 inch) in from the circumference (outer edge) of the circle of the fabric. You should now have two, concentric circles marked 2.5 cm (1 inch) apart, as shown diagram No. 7.

 

Diagram No 8

Mark the fabric for two buttonholes on each side, between the two concentric circles, as shown in diagram No. 8, marked in yellow. Later, this is where the cord will be threaded.

 
  Sew the two buttonholes on either side of the material, where marked.
 
 

Pin the circle of lining over the circle of fabric and stitch around the edge, leaving an opening of approximately 8 cm (3 inches), so that you can turn the bag out.


 
  Turn the bag out and hand press it completely around. This makes the job of ironing a lot easier.
 
  Iron the bag around the edges.

 

Diagram No 9 

Insert the plastic circle through the opening between the fabric and the lining. Position it in the centre of the bag, as shown in diagram No. 9, marked in blue.

 
  Pin the plastic circle in position and then stitch around it.
 
  Close the opening with stitches.
 
  Stitch all the way around both the marked concentric circles, on each side of of the buttonholes.

 
  Insert the cording through the buttonholes and tie the ends.
   
   
   

  Darby Cushion

   
 

Notions

"darby.pcs" design.
"bord.pcs" design.

 

 
  Instructions
   

Darby Design 

Mark the centre of your satin fabric. Stitch out the "darby" design.
 
 

Using a dinner plate as a template, mark a circle on the back of the fabric.

 
 

Sew the circle using a striaght stitch in order to provide a guide for the next stitch.

 
 

Using a side plate as a template, carefully position and mark the fabric with a smaller circle. This smaller circle should be positioned inside the larger circle, previously marked in 1.

 
 

Sew the inner circle using a straight stitch in order to provide a guide for the next stitch.

 
  Sew stitch No 02 L = .50 W = 4.5 using gold Madeira No. 8 thread.

 
 

To create an attractive, raised appearance to your needlework, sew stitch No. 02 W= .30 L = 6.0 over the top of the first stitch, using gold Madeira No. 8 thread.

 

Diagram No 1 

Sew stitch No. 111 L= 3.0 W= 6.0 over the the top of the satin stitch. using a tan thread as shown in diagram No. 1

 
 

Repeat the sewing procedures detailed in 6 to 8, above for the outer circle.

 

Diagram No 2 

Adjacent to the outer edge of the satin stitch of the inner circle, sew stitch No. 156 (mirrored) W= 6.0 L= 6.0 using tan coloured thread. Please refer to diagram No. 2.
 

Board 

As shown on the Darby Pillow at the top of the screen, stitch the "bord." design on the four sides of the pillow. The "bord" design is below

Darby Cushion 

  

Machine Embroidery Designs

 Latest Releases

 

Wild and Free Machine Embroidery Designs

Released on the 2nd February 2019

 

 Wild and Free Machine Embroidery Designs

  

6 designs included in the Wild and Free machine embroidery design set.

The Wild and Free design is suitable for a 6 x 10 inch or 240mm x 150mm hoop.

The Wild and Free design is available in DST, EMB, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart and instructions are included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EMB or EXP format. Sorry for the inconvenience.

 View the Wild and Free Machine Embroidery Designs

Contemporary Chic Machine Embroidery Designs by StitchingArt

 
Contemporary Chic Machine Embroidery Designs

 Released on the 4th December 2018

8 designs included in the Contemporary Chic machine embroidery design set.

The Contemporary Chic design is suitable for a 5 x 7 or 180mm x 130mm hoop.

The Contemporary Chic design is available in DST, EMB, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart is included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EMB or EXP format. Sorry for the inconvenience.

 View the Contemporary Chic Machine Embroidery Designs

 

 

New York Machine Embroidery Designs

 

New York Machine Embroidery Designs

 Released on the 11th November 2018

 13 designs included in the New York machine embroidery design set.

The New York design is suitable for a 5 x 7 or 180mm x 130mm hoop.

The New York design is available in DST, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart and instructions are included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EXP format. Sorry for the inconvenience.

View the New York Machine Embroidery Designs

 

 

 

Crinoline Lady Machine Embroidery Designs

 

Crinoline Lady Machine Embroidery Designs

 Released on the 4th November 2018

1 design included in the Crinoline Lady machine embroidery design set.

The Crinoline Lady design is suitable for a 6 x 10 inch or 240mm x 150mm hoop.

The Crinoline Lady design is available in DST, EMB, EXP, HUS, JEF, PES, VIP, VP3 and XXX.

The colour chart is included in the design set

As I am now digitizing with Wilcom embroidery software (which is a commercial software) we are unable to convert files to ART format. Bernina embroidery machines will now need to purchase designs in EMB or EXP format. Sorry for the inconvenience.

View the Crinoline Lady Machine Embroidery Design